Electronic Components

DC-DC Buck Module 5V 1.2A Output 6.5V to 15V DC Input - CE-DC-DC-LDOA-5DC-DC LDO is a DC-DC Module with a TO-220 form factor. This is designed to replace existing Linear regulators in use, like...

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you...

This sensor is a temperature detector used to test the liquid temperature based on 18b20. CHARACTERISTICS Standard 3-pin GVS ports are easy to plug. 3V working voltage can drive the micro:bit...

This is a wind speed sensor with a rain-proof design. It has a standard connector for Octopus brick series products. We can use it to test wind speed. It adopts three half-sphere bowls with a 6CM...

This is a colorful strip based on WS2812B beads, it can display the color RGB and support multiple cascades at the same time. Characteristics Standard 3-pin GVS ports are easy to plug. Both ends...

LEDs are NOT included Keep your 10mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open...

Attaching NeoPixel strips to your costume can be a struggle as the flexible PCBs can crack when bent too much. So how to add little dots of color? Use these stranded NeoPixel dots! They're very...

PIR sensors are used to detect motion from pets/humanoids from about 5 meters away (possibly works on zombies, not guaranteed). This sensor is much smaller than most PIR modules, which makes it great...

This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 100K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so...

Add a bright, hi-res, square LCD screen to your Raspberry Pi (or Pico) projects with this 1.54" Breakout Garden-compatible SPI display. Now it's super-easy to incorporate into other Raspberry Pi or...

Let your project know its place in the world with this tiny but ultra-sensitive global positioning breakout! This I2C breakout houses a PA1010D GPS receiver module with inbuilt ceramic antenna,...

An ultra-low-power ( ~100 nA), highly accurate real-time clock breakout. The RV3028 RTC breakout is perfect for adding timekeeping to your project and, thanks to the tiny on-board battery, it'll keep...

An easy, solderless, swappable way to use breakouts with your Raspberry Pi Pico - add up to three Pimoroni breakouts (2 x I2C and 1 x SPI) to the sturdy slots and get coding and creating! A...

Sometimes when you have too many choices, it's hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that's all you want. Well too bad, you are...

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features 465-470nm Blue 3.0-3.4VDC Forward Voltage 20mA Forward Current 40...

DC-DC Buck Module 3.3V 1.8A Output 4.5V to 15V DC Input - CE-DC-DC-LDOA-3.3DC-DC LDO is a DC-DC Module with a TO-220 form factor. This is designed to replace existing Linear regulators in use, like...

Take your next outdoor sensor project to the next level with this SHT-30 based temperature/humidity sensor. The sensor includes a dual-use sensor module from Sensirion in a sintered metal mesh...