The Kitronik Movement Module (Simple Servo Controller) provides a simple way of adding a 180-degree servo to your project without the need for code. The Movement Module is the perfect solution for simple animatronics functions, such as; opening and...

Make the Raspberry Pi Pico the core of your new buggy project with the Kitronik Compact Motor Driver Board for Raspberry Pi Pico. Make the Raspberry Pi Pico the core of your new buggy project with the Kitronik Compact Motor Driver Board for Raspberry Pi...

Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is very similar in size and specifications to the Hitec HS-55. This little guy is able to take in 6 volts and deliver 20.8 oz-in. of maximum torque at 0.10...

Build the hexapod/robot arm/other articulated contraption of your dreams with this all-in-one RP2040 powered servo controller with current measurement, sensor headers and RGB LEDs. Servo 2040 is a standalone servo controller for making things with lots...

Make the Raspberry Pi Pico the core of your new robotics project with the Kitronik Compact Robotics Board for Raspberry Pi Pico. This Compact Robotics Board enables the Raspberry Pi Pico (connected via pin header) to drive 4 motors (or 2 stepper motors)...

90 degree Plastic Gear Motor with wheel for your 2WD or 4WD robot cars. Specifications Voltage: DC 3V-6V Current: 100 MA-120MA Reduction rate:  48: 1 RPM (With tire): 100-240 Tire Diameter: 65mm Car Speed (M/minute): 20-48 Motor Weight (g): 29/each...

This module uses ST's L29GN as the main driver chip, featuring strong driving capability, low heat generation and strong anti-interference ability. It can use the built-in 78M05 to take power through the drive power supply part, but in order to...

This gearmotor consists of a low-power, 12 V brushed DC motor combined with a 377.93:1 metal spur gearbox. The gearmotor is cylindrical, with a diameter just under 25 mm, and the D-shaped output shaft is 4 mm in...

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft...

Looking to create your own personalized robot and require a frame to hold the range finding module? This kit comes preloaded with a HC-SR04 ultrasonic rangefinder, a tower pro SG92R servo and four wire DuPont female to female cable for connecting...

This gearmotor is a powerful brushed DC motor with 50:1 metal gearbox intended for operation at 12 V. These units have a 16 mm-long, 6 mm-diameter D-shaped output shaft. Note: Stalling or overloading gearmotors can greatly decrease their...

Want to add more sensors or an extra tier to your DiddyBorg v2?  Our Multifunction Top Kit allows you to extend your robot to do even more :) This version is in Clear Acrylic! With the Multfunction Top Kit fitted DiddyBorg v2 can now: ...

These are a pair of hobby gearmotors from DAGU. These gearmotors are the same ones recommended for use in SparkFun's Shadow Chassis and offer a cheap and easy-to-use setup to get your wheels turning. Each Hobby Gearmotor also possess a 9mm long output on...

This breakout board for STMicro’s STSPIN220 low-voltage microstepping bipolar stepper motor driver offers microstepping down to 1/256-step and operates from 1.8 V to 10 V, allowing stepper motors to be powered with voltages that are too...

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V. The board measures only 0.7" x 0.7" yet delivers a typical continuous output current of up...

This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 51.45:1 metal gearbox. It has a cross section of 10 x 12 mm, and the D-shaped gearbox output shaft is...

This version of Pololu's MP6500 Stepper Motor Driver Carrier with Potentiometer Current Control ships with male header pins installed as shown in the main product picture, so no soldering is required to use it with an appropriate 16-pin socket or...

This version of the Black Edition A4988 Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. This product is a carrier board or breakout...

This version of Pololu's STSPIN820 Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. This breakout board for STMicro’s STSPIN820...

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat...