Get ready to clacky to your heart's content. Here is a 10 pack of translucent keycaps for your next mechanical keyboard or NeoKey project. Snap them onto a Cherry MX or compatible switch to turn your Feather or breakout into the lil'est macro keypad. The...

It's half USB Key, half Adafruit Trinket, half mechanical keeb...it's NeoKey Trinkey, the circuit board with a Trinket M0 heart, a NeoPixel glow, and a Cherry MX-compatible. We were inspired by single-key macro pads we've seen. So we thought, hey what if...

For crafting your very own custom keyboard, these Kailh White Linear mechanical key switches are deeee-luxe! With smooth actuation and Cherry MX compatibility, they're lovely when you want a clicky tactile keystroke with a snappy feel and an audible...

16mm Metal Annular Push Button Switch - 3-6V - Momentary - Flat Head - Green LED Ring These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that...

This thumbstick is an analog joystick - more accurate and sensitive than just 'directional' joysticks - with a 'press in to select' button. Since it's analog(10k potentiometers), you'll need two analog reading pins on your microcontroller to determine...

Material: PlasticColor: RedVoltage: 3A 125VLeads: Solder lugsContacts configuration: SPSTSwitch method: OFF / ON

The Squid Button makes it super easy to attach a push switch to a Raspberry Pi. Note: Switch and lead colors may vary The Squid Button is in fact a momentary action push switch with trailing leads that end in female header sockets that will...

Squeeze once to turn on, squeeze again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's easy to embed in a seam for easily powering up/off wearable and fabric projects. Can handle up to 14V and...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front...

This is a resistive analog joystick, very similar to those found on the PSP1000. These compact joysticks are different in that they have a very interesting €˜slide' feeling. For wiring this part, if you look at the device from the bottom the pin out...

These Sensor might come in different colors other than blue DC 6-36V NPN 3-wire 8mm Inductive Proximity Sensor Switch Detector LJ18A3-8-Z/BY Product Description Metal shell, DC type, 8mm detecting distance, 3 wire system. Power supply...

By popular demand, we now have these buttons with a full color RGB LED ring light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. Simply drill a 16mm hole into any material up to 1/4" thick and you can fit these in...

Micro-switches are often found in arcade buttons and joysticks but they're also really handy in any kind of mechatronics project or when you need a basic sensor. They are always 'tactile' (clicky feeling), and 'momentary' (the switch closes when pressed,...

Medium-sized clicky momentary switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as shown in this tutorial. The pins are normally open (disconnected) and when the button is...

The Adafruit Push-button Power Switch is a tidy little design that lets you control a DC power source using an everyday tactile button. The breakout uses a latching analog circuit that is triggered by a push of the button. Press once to turn on, then...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of...

This mini-kit makes it easy to mount a PSP/Xbox-like thumb joystick to your project. The thumbstick is an analog joystick - more accurate and sensitive than just 'directional' joysticks - with a 'press in to select' button. Since it's analog, you'll need...