If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this USB C Jack to USB C Jack Round Panel Mount Plug is the easiest and fastest way to panel-ify your project. It's about 30mm in...

Waveshare 15817 - USB To RS232/485/TTL Interface Converter, Industrial Isolation This is an industrial USB to RS232/485/TTL isolated converter with original FT232RL inside. It features embedded protection circuits such as power isolation, ADI magnetical...

Multifunctional USB Power Meter - LCD Color Display - USB / Micro USB / USB-C A handy tool that measures voltage, current, power, charge time, and more for all of your USB A, Micro B, and USB C gadgets (phones, power banks, etc...) Features ...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port. Please Note: FOR USE ONLY WITH 5 VOLT supplies and...

USB A-Male to USB Micro-B Cable - 3ftPerfect for Micro:bit and some Arduino boards!

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB OTG data over a separate USB-C connection. USB Type-C (DATA POWER) <> USB Type-C (USB2 DATA) and USB Type-C...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB Type-A Female 4 - 6way long pin header Of the 6 pins on the connector boards two are used for 5V...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB) and Power (Micro USB/Barrel jack). USB Type AMicro...

Waveshare 17939 - Industrial USB TO TTL Converter, Original FT232RL Onboard, Multi Protection Circuits, Multi Systems Support USB signal & Pinouts Definition 5V 5V output VCC 3.3V or 5V output, configured by switch GND Ground TXD...

USB To TTL, With Embedded Convertor USB to TTL 4-pin Wire specification: Embedded convertor: PL2303 Supports windows XP/7/8/8.1/10/... Connector: USB Type-A plug, 4-pin 2.54mm pinheader Pinout: Red - VCC (5V) Black - GND Green - TXD (3.3V TTL,...

USB 3.0 SuperSpeed adapters are a great way to quickly change the connection type or gender of an existing USB cable. This adapter has USB Type C Male opposite USB 3.0 Type A Female.  Features Connector A: USB Type C Male Connector B: USB...

USB Type-C to USB 3.0 A-Male Cable - 5FT

USB Type-C to USB 2.0 A-Male Cable - 5ft

USB Type-C to USB 2.0 A-Male Cable - 3ft

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter can still be soldered to the GPIO header). The adapter...

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN / 5V When the EN pin is connected to >2V (5V max) power to...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC drivers on most modern operating systems (Win10/Linux/Mac OS...

Need more gigabytes on your Pi? Connect a SATA hard disk or SSD to your Raspberry Pi with this compact, high-performance USB 3.0 to SATA adapter. Great for storing media, games, data, or backing up your projects! This new version of our USB to...

USB 2.0 A MALE TO L-SHAPE MICRO B MALE CABLE, 3FT

USB 2.0 A MALE TO L-SHAPE MICRO B MALE CABLE, 1.5FT