Categories - PiShop.ca

Sub Categories

Hey, listen up! It's the world's smallest USB microphone! OK maybe it's not in the Guinness Record Book, but it is pretty darn small! This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with...

Add to Cart

Adafruit 3342 2×40 right-angle edge connector for micro:bit, fits on custom PCB.

2x40 Right Angle Edge Connector for micro:bit

$5.95 $8.95

This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this...

Add to Cart

UniPiCase Zero - Camera

$9.95

The PiShop UniPiCase Zero - Camera is a compact case designed for the Pi Zero. Its domed lid supports mounting of Official Raspberry Pi Cameras, with a slot for camera cables beneath the case. All ports remain accessible, while...

Add to Cart

Mongoose OS & Google IoT Core Pack w/ Adafruit Feather HUZZAH32

$70.34

In collaboration with Google and Mongoose OS, Adafruit's releasing an IoT Core Pack based around their Feather HUZZAH32! This kit includes a pre-soldered Adafruit Feather HUZZAH with ESP32 WiFi and some sensors and components to get...

Notify Me

UniPiCase Zero - Standard

$9.95

The UniPiCase is a secure, feature-rich case made to the best design and fabrication standards. This is our own case design, and it is manufactured here in Canada! Please note, this case is not compatible with the Zero WH. Only Tall versions of the case...

Add to Cart

MicroUSB Power Adapter 5V, 3A - International Plugs

$12.95

Specs: Plug Type: Aus, Euro, US Input Voltage AC: 100V - 240V Output Voltage Nom. 5V Output Current Max: 3A Power Supply Output Type: Fixed Output Connector: USB Micro Cable Length : 45 inch

Add to Cart

Butterfly PCB

$3.95

Allows two HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected *except* ID_SD and ID_SC (HAT EEPROM) which have solder jumpers - this allows HAT which follow the specification correctly to operate...

Add to Cart

Camera Cable Joiner/Extender for Raspberry Pi

$4.75

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that's simply not long enough. This lovely little board lets you add extension cables to your existing camera cable, giving you as much range as you'll...

Add to Cart

Cluster HAT v2.5

$51.95

Cluster Hat Version 2.5 by 8086 Consultancy The Cluster HAT interfaces a (Controller) Raspberry Pi A+/B+/2/3/4 with up to 4 Raspberry Pi Zeros (1.1/1.2 or W) configured to use USB Gadget mode, and is an ideal tool for teaching or...

Add to Cart

SD Card Imaging with Custom Software

$1.95

Need to deploy a lot of Pis? We can image SD cards for you and save you time (and possibly troubleshooting efforts). We use high quality card duplicators and perform low-level block by block cloning to ensure accurate, bootable images. Note that...

Add to Cart

Brass 12mm Standoff Set for Pi HATs - Pack of 4

$1.95

We tried several standoff kits before we chose this high quality set as our go-to. The metal hardware threads together cleanly, and the tall standoffs and nuts can be easily attached with your fingers, and then optionally tightened with tools. This 12mm...

Add to Cart

IDC 16 pin(2 x 8) ribbon cable - 30cm

$1.45

IDC Connector Pitch:2.54mm Cable Pitch:1.27mm Cable Length: 30cm Number of Wire: 16 Wires Conductor: 7/0.10mm(Tin Plated Copper) Two 2.54mm pitch 2x8Pin female IDC connectors on each end.

Add to Cart

Panel mount right angled USB cable -25cm

$3.95

25cm 90 Degree Right Angled USB 2.0 A Male Connector to Female Extension Cable With Panel Mount Hole Length: 25cm USB-A Male: 90 Degrees up Direction Angled type USB-A Female: With Panel Mount Hole

Add to Cart

BeoCreate 4-Channel Amplifier

$299.95

The Beocreate is a joint project between audio legends Bang & Olufsen and HiFiBerry. It is a very flexible 4-Channel DSP/DAC/amplifier combination board designed for high-quality music playback in combination with passive loudspeakers. It can be a...

Add to Cart

Resistor 560 OHM - Pack of 10

$1.45

This is a 10 Pack of 560 Ohms Resistors. 560 Ohms ±5% 0.25W, 1/4W through hole resistor with flame retardant coating and a safety carbon film. Datasheet

Notify Me

PUD HAT (Pull-Up/Down Resistor HAT)

$11.95 $13.95

Whether you're pulling-up or pulling-down, there's no need to frown! With the PUD HAT from ModMyPi, adding multiple pull-up or pull-down resistors to your Raspberry Pi project is easy! The PUD HAT is an expanded version of the smaller PUD board...

Notify Me

Raspberry Pi Prototyping HAT

$11.63

Design your own Raspberry Pi HAT, attach custom circuits, LEDs, IC's, potentiometers and more, with our Raspberry Pi Prototyping HAT! The HAT consists of a 0.1" prototyping soldering grid for attaching your peripherals with breadboard style traces for...

Notify Me

Triple GPIO Expansion Board w/ HAT Area

$11.95

This triple GPIO multiplexing expansion plate is perfect for sharing GPIO pins between applications and circuits! It's often fiddly to combine multiple breakout boards onto the standard single Pi GPIO header, but with the expansion plate, it's a breeze...

Notify Me

ModMyPi MCP23017 pHAT - 16 Channel I/O Expansion (Zero)

$14.95

The MCP23017 pHAT from ModMyPi and BuyaPi.ca is the perfect I/O expansion pHAT for your Raspberry Pi Zero. The pHAT features a single removable MCP23017 DIP IC, which utilise two i2c pins (which can be shared with other devices if...

Add to Cart

Pi Zero USB Stem

$7.95

The Zero Stem is a PCB shim that turns a Raspberry Pi Zero into a USB dongle. Once the shim is installed, your Raspberry Pi can be plugged directly into a computer or USB hub without any additional cables or power supplies. The Zero Stem is compatible...

Add to Cart