Categories - PiShop.ca

Sub Categories

micro:bit Passive Infrared Movement Detector

$7.95 $10.95

A small version of the PIR that is used in a typical burglar alarm. It triggers when a warm body passes in front of the detector. It has some range / sensitivity setting capability and the duration of the output can be set. The black lead goes on to...

Add to Cart

micro:bit Sound Level Detector

$8.45 $9.50

A small microphone with amplifier & threshold setting. It can detect when sound reaches a certain level. It can not detect a particular frequency and there is no support in the micro:bit programming environment at present for it to analyse...

Add to Cart

micro:bit Piezo Buzzer

$3.95 $5.95

A type of buzzer - it has to be driven by a pulsed output. It's tuned for around 2kHz when it will be at its loudest but will produce a tone across a wide range of frequencies. In the Block Editor, the black lead goes on to GND and the blue lead goes on...

Add to Cart

micro:bit Servo

$11.95

A small motor that moves it's output arm to a position depending on the signal sent to it with a reasonable degree of accuracy & repeatability. The brown lead with the black croc clip goes on to GND, the yellow lead goes on to the Pin 0, 1 or 2 that...

Notify Me

micro:bit Microswitch

$3.95 $4.95

Good for detecting boxes, drawers or doors being opened and much more. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2. This item is somewhat polarity sensitive, the red & black leads need...

Add to Cart

micro:bit Temperature Sensor

$7.95 $9.75

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead...

Add to Cart

micro:bit LDR Light Sensor

$4.95 $7.25

An external light sensor for all your light sensing needs. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2.This item is polarity sensitive, the red & black leads need to be on the correct...

Add to Cart

micro:bit Pushbutton

$3.95 $4.95

This Pushbutton makes it easy to add an extra input to your BBC micro:bit projects. With simple clip leads and no soldering required, it’s perfect for classrooms, workshops, and quick prototyping. Features Simple connectivity — attach...

Add to Cart

micro:bit Potentiometer

$5.95 $7.95

Provides a variable voltage to an analog input via a twist knob - a volume control if you will. Can be used for any application where a user input across an analog range is required - for instance changing the frequency of the music output or the speed...

Add to Cart

micro:bit Water Sensor

$7.50

The Water Sensor Provides a variable analog reading depending on how wet/damp the sensor is. Good for plants or fingers. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on whichever pin is being used in the program. This...

Notify Me

3x4 Right Angle Male Header - 4 pack

$3.95

Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or...

Add to Cart

DiddyBorg v2 Multifunction Top Kit

$21.02

Want to add more sensors or an extra tier to your DiddyBorg v2? Our Multifunction Top Kit allows you to extend your robot to do even more :) With the Multfunction Top Kit fitted DiddyBorg v2 can now: Attach two servos to the top...

Notify Me

Mini Black HAT Hack3r – Fully Assembled

$19.95

Mini Black HAT Hack3r – Fully AssembledNeed to detach or debug your HAT? Then the Mini Black HAT Hack3r is for you! A nifty little tool that lets you access all of the GPIO pins while also running a HAT. Ideal for debugging your HAT projects or...

Add to Cart

:MOVE mini Line Follower Interface cable

$2.45

Dupont 5 way Female to Female interface cable for the Kitronik Line Following Add On For :MOVE mini kit. It is also suitable for breadboards with 2.54mm pitch. This standard Dupont interface cable is the cable used in the Kitronik Line Following Add...

Notify Me

Bumper Add-On For The :MOVE MINI

$3.95

Get more from :MOVE mini for the BBC microbit with the Bumper add-on. Turn :MOVE mini into a football/hockey game playing robot and compete against other robots. The BBC micro:bit is sold separately and the kit requires simple assembly, buy the...

Add to Cart

:GAME ZIP 64 for the BBC micro:bit

$50.95

The Kitronik :GAME ZIP 64 is the ultimate retro gaming accessory for the BBC microbit. It has been designed to be an all in one hand held gaming platform, which also includes a built in, 64 (8x8) individually addressable full colour ZIP LED, screen...

Add to Cart

MI:power Case for the BBC micro:bit - Orange

$6.95

Compatible with micro:bit V1 only! Caution! The BBC micro:bit, and MI:power board are NOT included. This is the ORANGE version of this case. This case has been designed to protect a BBC micro:bit with...

Notify Me

MI:power Case for the BBC micro:bit - Clear

$7.95

Clearance: Compatible with micro:bit V1 only! Caution! The BBC micro:bit and MI:power board (required) are NOT included. This is the CLEAR version of this case. This case has been designed to protect a BBC micro:bit with...

Notify Me

MI:power board for the BBC micro:bit

$7.95

CLEARANCE! This product is compatible with micro:bit V1 ONLY! The MI:power board for the BBC micro:bit brings real portability to your wearable projects. The stylish, lightweight PCB is designed to fit snugly against the BBC micro:bit and features a...

Notify Me

E-Textiles Kit for the BBC micro:bit

$14.95

This kit is a great way to get started with creating BBC micro:bit controlled E-Textiles projects and designs. We have selected a number of products from our Electro-Fashion range, including five regular 5mm LEDs, ten of our ultra-slim LEDs, ten...

Notify Me