Electronic Components

This is a 25 Pack of 1K Ω Resistors. 1k Ohm, 1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards.

Need some indicators? We are big fans of these diffused green LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a...

Need some indicators? We are big fans of these diffused red LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a...

Need some indicators? We are big fans of these diffused blue LEDs, as featured in the LoL shield. They are really bright so they can be seen in daytime, and from any angle. They go easily into a...

The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be added to a microcontroller by converting data between...

PowerBoost is the perfect power supply for your portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your...

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides an audio output, but also a binary indication of the...

Resistors are a good thing, in fact, they're actually crucial in a lot of circuit designs. The only problem seems to be that resistors disappear into thin air. The only way to be sure that you're...

A stepper motor to satisfy all your robotics needs! This 4-wire bipolar stepper has 1.8° per step for smooth motion and a nice holding torque. The motor was specified to have a max current of 350mA...

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of...

Adafruit 2471 - HUZZAH ESP8266 Breakout Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! The ESP8266 processor from Espressif is an 80 MHz...

The SparkFun Large Digit Driver is a chainable controller backpack that can be soldered directly to the back of a large 6.5" 7-segment displays. Large numerical displays are a great addition to any...

This is an open sourced ISP (In-System Programming) programmer available from http://www.fischl.de/usbasp/.This is provided as an accessory to MicroHOPE due to several reasons. If you want to develop...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber...

This rotary encoder is the best of the best, its a high quality 24-pulse encoder, with detents and a nice feel. It is panel mountable for placement in a box, or you can plug it into a breadboard...

Keep your 5mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening...

Non-invasive current transformer, use this sensor clip to build your own Personal Energy Monitor . Model: T17－05 Note:Color might change due to different batchs.  

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin 0.6" wide version. Best used with chips that have...

The DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the...