Categories - PiShop.ca

Sub Categories

Click Me to Download the Instructions for this kit. The Servo Kit for micro:bit makes it easy to connect up three servomotors from your micro:bit. Not only that, but the kit also comes with three servomotors and a battery box. Just add a micro:bit and...

Choose Options

Power for micro:bit

$13.95

The MonkMakes Power for micro:bit opens up lots of ways of powering your micro:bit. This tiny board has a standard DC barrel jack socket at one end and provides a regulated 3.3V output that you can use to power your micro:bit using the JST battery...

Add to Cart

Servo for micro:bit

$14.95

The MonkMakes Servo for micro:bit provides a really easy way to attach up to three servomotors to a BBC micro:bit. The board requires a power supply or battery pack to provide 5 or 6V to the servomotors. It includes a voltage regulator that will...

Add to Cart

MicroSD Card Ultra - 128GB - Class 10, A1 - Blank

$19.95

Transfer speeds of up to 100MB/s** Rated A1 for faster app performance3 and UHS Speed Class U1 and Speed Class 10 for Full HD video recording and playback1 Shockproof, temperature-proof, waterproof, and X-ray-proof2

Add to Cart

MMC (micro SD) HAT for the Raspberry Pi

$20.95

This HAT disables WiFi on Raspberry Pi 3B and 3B+ The MMC HAT adds a second micro SD socket to your Raspberry Pi using the second SDIO interface. Please note that the MMC HAT is only officially supported on Raspberry Pi OS. The MMC HAT has many...

Notify Me

I2C Multiplexer (8 way) pHAT for Raspberry Pi

$13.95

The I2C multiplexer allows connecting multiple I2C devices with the same address onto a single I2C bus (PCB colour may vary). For each multiplexed output there are 4 pins - data ports SDAx, SCLx GND ground and V for power. The "V" output can be altered...

Add to Cart

Giant Butterfly PCB

$5.45 $6.45

Allows four HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected, ID_SD and ID_SC (HAT EEPROM) have cuttable solder jumpers. For HAT/pHAT with an EEPROM (required by the HAT specification) you will...

Choose Options

Solderless Serial to USB adapter for Raspberry Pi Zero

$12.95

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter can still be soldered to the GPIO header). The adapter...

Add to Cart

USB Power Switch

$4.95

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN / 5V When the EN pin is connected to >2V (5V max) power...

Notify Me

USB CDC Serial Adaptor (3.3v)

$6.45

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial on a Raspberry Pi and for Arduino programming (using RTS...

Add to Cart

USB Console Stub - Serial adaptor for Raspberry Pi

$6.45

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC drivers on most modern operating systems (Win10/Linux/Mac OS...

Add to Cart

SparkFun Air Quality Sensor - SGP30 (Qwiic)

$27.95

The SparkFun SGP30 Air Quality Sensor provides information on the quality of the air in your room or house by monitoring the volatile organic compounds around the sensor. The SGP30 Air Quality Sensor can return valid indoor air quality (IAQ) readings...

Notify Me

DC-DC 12V to 3.3V 5V 12V Power Module Multi Output Voltage Conversion

$2.45

This DC-DC 12V to 3.3V 5V 12V Power Module Multi Output Voltage Conversion is also known as Buck Converter or also as Step-Down Voltage Converter. The module is capable of altering the output of the power source/supply before...

Notify Me

RS232 Board

$5.95

RS232 Communication Board, SP3232 On Board, 3V-5.5V, ESD Enhanced, Hardware Flow Control Supported Overview The RS232 Board is used for establishing RS232 communication with devices powered from 3V - 5.5V. It contains SP3232 (RS-232...

Add to Cart

MAX 485 Module / RS- 485 Module / TTL to RS- 485 Converter Module

$2.50

Features: On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. On board then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. All pins of chip have been lead to can be...

Notify Me

Stackable acrylic case for FOUR Raspberry Pi 4

$24.95

Features This case just has top and bottom boards, so you can access the Raspberry Pi from all sides There is a cooling fan for each layer The acrylic material won't block the Wi-Fi and Bluetooth signal You can stack many layers on it, suitable for DIY...

Add to Cart

Stackable acrylic case for THREE Raspberry Pi 4

$19.95

Add to Cart

Stackable acrylic case for TWO Raspberry Pi 4

$11.95

Add to Cart

SATA SSD to USB Adapter

$9.95

Need more gigabytes on your Pi? Connect a SATA SSD to your Raspberry Pi with this compact, high-performance USB 3.0 to SATA adapter. Great for storing media, games, data, or backing up your projects! This new version of our USB to SATA...

Add to Cart

4 & 40 Pin Extra Tall Header (Push Fit Version) - POE HAT Set

$3.95

Stack on top of your official POE HAT with this custom-made extra-tall 2 x 2 pin female header and 2 x 20 pin female header. This is a set of two headers which allows you to stack a POE HAT and another HAT on top of your Raspberry Pi This is...

Add to Cart