Categories - PiShop.ca

Sub Categories

Google AIY Voice Kit for Raspberry Pi - Starter Pack

$89.95 $99.95

Need directions to your nearest dry cleaner? Or maybe you need to send a hands-free email? Perhaps you just want to know what the weather's like in Timbuktu. Ask your new little friend - theÂ Google AIY Voice Bot! This Starter Pack provides the Google...

Notify Me

7 inch 800 x 480 Raspberry Pi 3 LCD Touch Screen Module

$69.95 $79.95

Notify Me

MicroUSB Power Adapter 5V, 3A - International Plugs

$12.95

Specs: Plug Type: Aus, Euro, US Input Voltage AC: 100V - 240V Output Voltage Nom. 5V Output Current Max: 3A Power Supply Output Type: Fixed Output Connector: USB Micro Cable Length : 45 inch

Add to Cart

Butterfly PCB

$3.95

Allows two HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected *except* ID_SD and ID_SC (HAT EEPROM) which have solder jumpers - this allows HAT which follow the specification correctly to operate...

Add to Cart

Camera Cable Joiner/Extender for Raspberry Pi

$4.75

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that's simply not long enough. This lovely little board lets you add extension cables to your existing camera cable, giving you as much range as you'll...

Add to Cart

Cluster HAT v2.5

$51.95

Cluster Hat Version 2.5 by 8086 Consultancy The Cluster HAT interfaces a (Controller) Raspberry Pi A+/B+/2/3/4 with up to 4 Raspberry Pi Zeros (1.1/1.2 or W) configured to use USB Gadget mode, and is an ideal tool for teaching or...

Add to Cart

SD Card Imaging with Custom Software

$2.45

Need to deploy a lot of Pis? We can image SD cards for you and save you time (and possibly troubleshooting efforts). We use high quality card duplicators and perform low-level block by block cloning to ensure accurate, bootable images. Note that...

Add to Cart

Brass 12mm Standoff Set for Pi HATs - Pack of 4

$1.95

We tried several standoff kits before we chose this high quality set as our go-to. The metal hardware threads together cleanly, and the tall standoffs and nuts can be easily attached with your fingers, and then optionally tightened with tools. This 12mm...

Add to Cart

IDC 16 pin(2 x 8) ribbon cable - 30cm

$1.45

IDC Connector Pitch:2.54mm Cable Pitch:1.27mm Cable Length: 30cm Number of Wire: 16 Wires Conductor: 7/0.10mm(Tin Plated Copper) Two 2.54mm pitch 2x8Pin female IDC connectors on each end.

Notify Me

Panel mount right angled USB cable -25cm

$3.95

25cm 90 Degree Right Angled USB 2.0 A Male Connector to Female Extension Cable With Panel Mount Hole Length: 25cm USB-A Male: 90 Degrees up Direction Angled type USB-A Female: With Panel Mount Hole

Add to Cart

RJ45 Panel Mount Extension Cable - 30cm

$2.95 $3.95

Notify Me

BeoCreate 4-Channel Amplifier

$299.95

The Beocreate is a joint project between audio legends Bang & Olufsen and HiFiBerry. It is a very flexible 4-Channel DSP/DAC/amplifier combination board designed for high-quality music playback in combination with passive loudspeakers. It can be a...

Add to Cart

Resistor 560 OHM - Pack of 10

$1.45

This is a 10 Pack of 560 Ohms Resistors. 560 Ohms ±5% 0.25W, 1/4W through hole resistor with flame retardant coating and a safety carbon film. Datasheet

Notify Me

ATmega2560-16AU

$9.95

The high-performance, low-power Microchip 8-bit AVR RISC-based microcontroller combines 256KB ISP flash memory, 8KB SRAM, 4KB EEPROM, 86 general purpose I/O lines, 32 general purpose working registers, real time counter, six flexible timer/counters with...

Notify Me

micro:bit Battery Holder - 2xAA (JST-PH)

$1.95

This is a unique two-cell AA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH connector. The connector mates the JST socket on the micro:bit perfectly, allowing you to easily make your...

Notify Me

Serial Enabled 20x4 LCD - Black on Green 5V

$34.94

This is the latest evolution of SparkFun's serial LCD. Included on a single board is a 20x4 LCD and an embedded circuit based around a PIC 16F88. The on-board PIC takes a TTL serial input and prints the characters it receives onto the LCD. The installed...

Notify Me

Christmas Tree Programmable Kit OLD

$12.95

The perfect Raspberry Pi stocking filler this Christmas! The Christmas Tree programmable kit is the designed for any maker or hacker and ideal kit for people new to Raspberry Pi or even the experienced users who want to practice the art of...

Notify Me

Raspberry Pi T-Cobbler PRO Breakout

$10.95

Ready to get PRO with your Raspberry Pi breakout boards? Our T-Cobbler PRO has all the same nifty features as the standard T-Cobbler breakout, but with added power control to help your projects go further! This neat little...

Notify Me

PUD HAT (Pull-Up/Down Resistor HAT)

$11.95 $13.95

Whether you're pulling-up or pulling-down, there's no need to frown! With the PUD HAT from ModMyPi, adding multiple pull-up or pull-down resistors to your Raspberry Pi project is easy! The PUD HAT is an expanded version of the smaller PUD board...

Notify Me

Zero Prototyping pHAT (Zero)

$8.95

Design your own Raspberry Pi Zero pHAT, attach custom circuits, LEDs, IC's, potentiometers and more, with our Raspberry Pi Zero Prototyping pHAT! The pHAT consists of a 0.1" prototyping soldering grid for attaching your peripherals with breadboard style...

Notify Me