Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink! This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi  but is best paired with a...

Dual Supply for Raspberry Pi (A+/B+/2B/3B/3B+) Power from each Micro USB connector goes via a MOSFET "Ideal Diode" which is then connected directly to the Micro USB socket on the Raspberry Pi. Data pins are not connected from either Micro USB port (as...

Connect your Raspberry Pi Zero or Pi Zero W directly to your computer for use as a USB Gadget device (USB Ethernet / Serial / Ethernet+Serial / etc.) or just for power. Works with all public versions of Raspberry Pi Zero. Can also be used with 8086's...

If you're looking for the most compact li'l display for a Raspberry Pi (most likely a Pi Zero) project, this might be just the thing you need! The Adafruit 128x32 PiOLED is your little OLED pal, ready to snap onto any and all Raspberry Pi...

Hey, listen up! It's the world's smallest USB microphone! OK maybe it's not in the Guinness Record Book, but it is pretty darn small! This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with...

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that's simply not long enough. This lovely little board lets you add extension cables to your existing camera cable, giving you as much range as you'll...

Cluster Hat Version 2.5 by 8086 Consultancy The Cluster HAT interfaces a (Controller) Raspberry Pi A+/B+/2/3/4 with up to 4 Raspberry Pi Zeros (1.1/1.2 or W) configured to use USB Gadget mode, and is an ideal tool for teaching or...

This time he's taken a pass at a Pi Protector for Raspberry Pi Zero, Zero W, and Zero 2W, not quite a full case, it will keep your Pi Zero safe and svelte. Keep your Raspberry Pi® Zero computer tidy and safe in this lovely clear...

This board makes connecting wires to the Raspberry Pi GPIO incredibly easy.  It's a reference board that makes it really simple to see if you're connecting your wires correctly. It's only 0.8mm thick, idiot proof (you can't put it on backwards...),...

Need to add analog inputs? This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use, and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the...

Add a power switch to any USB-powered project simply by plugging this between the USB power port and the USB cable. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a USB A...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these...

Ever since Altoids discontinued the Gum version, its been hard to get tins. So Adafruit went and got a whole mess of them custom made! These tins are exactly the same shape and size as the old Altoids gum tins but they are blank and they got the bottom...

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably...

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2,Pi 3, Pi 4! Or just any Pi with 2x20 connector. The Raspberry Pi B+ and Pi 2 has landed on the Maker World like a 40-GPIO...

You got a Raspberry Pi Model B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic 26-pinout. Very frustrating, it is...unless you have this ingenious 'downgrade' GPIO cable. It has a 40-pin socket...