The Kitronik LED Strip with Solder Free Connections is a board designed for low-power lighting, such as desk lamps or accent lights. The board is designed to require no soldering and only minimal tool use connecting wires to the power supply terminal...

Waveshare 24594 - Waveshare RP2040-Matrix Development Board, Onboard 5×5 RGB LED Matrix, Based On Official RP2040 Dual Core Processor Specifications RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom Dual-core...

This cool mechanical encoder has five buttons (up, down, left, right and centre) and a rotary scroll wheel (with satisfying clicky detents). We've surrounded it with 24 twinkly RGB LEDs and turned it into a handy, pre-assembled I2C breakout so it's...

So, you want lots and lots of NeoPixels? And you want them for less? Not a problem! Here's a sheet of Breadboard-Friendly NeoPixel breakouts fresh from the (reflow) oven. Snap them off as you need 'em and save a pretty penny while you're at it. Each...

This super-cute 5x5 RGB LED matrix breakout is a neat way to visualise sensor data or for simple animations or notifications, and it's Raspberry Pi and Arduino-compatible. These little matrices are ideal for visualising data from other Pimoroni...

Bring a little bit of Times Square into your home with this sweet 32 x 32 square RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short...

The LilyTiny is a tiny little LilyPad board designed to add flashy functionality to your project without taking up a lot of room. Even though it's as small as some of the LilyPad sensors, this board actually has an ATtiny microcontroller on it so it's...

These are the smallest NeoPixel breakouts around! Tiny, bright RGB+White pixels to your project. These little PCBs are only 9.1mm x 9.1mm and have two sets of three pads on the back for soldering wires. These ultra-bright LEDs have a constant-current...

This is a colorful strip based on WS2812B beads, it can display the color RGB and support multiple cascades at the same time. Characteristics Standard 3-pin GVS ports are easy to plug. Both ends are equipped with a connector and it supports multiple...

LEDs are NOT included Keep your 10mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into...

Attaching NeoPixel strips to your costume can be a struggle as the flexible PCBs can crack when bent too much. So how to add little dots of color? Use these stranded NeoPixel dots! They're very small, so they're easy to embed into any structure, costume,...

Sometimes when you have too many choices, it's hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of each, that's all you want. Well too bad, you are getting two of each! The LED Rainbow Pack contains two...

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features 465-470nm Blue 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 100-150 MCD...

The only thing better than a nice mechanical key is, perhaps, FOUR mechanical keys that also can glow any color of the rainbow - and that's what the Adafruit NeoKey 1x4 QT I2C Breakout will let you do! This longgg 3" x 0.8" PCB fits...

Adding glowy color to your projects has never been easier: no more soldering or stripping wires, clip 'em on and glow! This Adafruit NeoPixel LED Strip with Alligator Clips has 30 total LEDs in a "60 LED per meter" spacing, and is 0.5 meters long, in...

A programmable 53 x 11 LED matrix / sign with wireless connectivity and oodles of extras! Galactic Unicorn is a very beautiful, all-in-one, RP2040 powered LED matrix perfect for conveying information fabulously (or for sprucing up your desktop,...

The Kitronik TriColour LED board is a pre-built strip board designed for low-power lighting displays, such as edge-lit signs and illustrations. It has been designed such that its power requirement is within the supply rating of a computer USB port (under...

An LED Bulb for use with microcontrollers. The board is designed to make it super-easy to attach a high brightness bulb to a Raspberry Pi, Pico, Arduino, ESP32 or other microcontroller board. 3V to 6V operation Built-in MOSFET for PWM and on/off...

There are got all sorts of diffused bare LEDs in all sorts of colors and sizes. But have you ever laid your paws on this set of kitty-shaped LEDs? These look too cute and charming and will look amazing for any electronics...

We've got all sorts of diffused bare LEDs in all sorts of colors and sizes. But have you ever laid your peepers on this stunning set of sphere-shaped LEDs? These look too cute and charming and will look amazing for any...