These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug...

These are very interesting 5mm diffused RGB LEDs - instead of having 4 pins to control 3 LEDs, they have only two leads - power and ground. When powered, the LEDs perform a slow fade through the rainbow, from red to orange to yellow, etc till they get...

Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel (3A peak) using the TB6612. These are perhaps better known as "the drivers in our assembled Adafruit Motorshield or Motor HAT." We...

Adafruit 2895 - Non-Latching Mini Relay FeatherWing A Feather board without ambition is a Feather board without FeatherWings! This is the Non-Latching Mini Relay FeatherWing. It gives you power to control, and control over power. Put simply,...

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standard, yellow LED. The lens is 3mm in diameter and it is diffused. 2.0-2.4VDC forward drop Max current: 20mA...

Need some indicators? We are big fans of these diffused green LEDs, as featured in the LoL shield. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project...

Need some indicators? We are big fans of these diffused blue LEDs, as featured in the LoL shield. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project...

PowerBoost is the perfect power supply for your portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. Like our popular 5V 1A USB wall...

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull (from...

Adafruit 2471 - HUZZAH ESP8266 Breakout Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! The ESP8266 processor from Espressif is an 80 MHz microcontroller with a full WiFi front-end (both as...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of...

This rotary encoder is the best of the best, its a high quality 24-pulse encoder, with detents and a nice feel. It is panel mountable for placement in a box, or you can plug it into a breadboard (just cut/bend the two mechanical side tabs.) We also...

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these 0.1" pitch terminal blocks. There's a little spring contact so you can pull back on the plastic bit and...

Keep your 5mm LEDs in place with these little plastic LED holders. These are handy for projects using individual LEDs as they look sleek, and your LED won't budge. Slot the LED through the opening and you'll get a nice *snap* into place. Comes as a...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of...

An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 28 pin 0.6" wide version. Best used with chips that have 28 pins (2x14) and have 0.6" pin spacing. We also have 0...

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal points on each digit and an extra wire...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each shell comes with a two-part snap plastic shell and a proper...

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards...

This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards. They will work where "thick pin"...