This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and...

Caution! This product is NOT compatible with the new Raspberry Pi Zero W 2 Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter can still be soldered to the GPIO header). The adapter...

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN / 5V When the EN pin is connected to >2V (5V max) power...

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial on a Raspberry Pi and for Arduino programming (using RTS...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC drivers on most modern operating systems (Win10/Linux/Mac OS...

These little cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits, and have a few handy in our ARM-dev box. We thought you may...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or...

If you're looking to make a custom cable with any two of our USB or HDMI adapters, then you'll need to have these flex cables handy! Making custom cables has never been easier. Just grab one of these cables, then swap and switch any of the plug or...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable...

Adafruit 3556 - DIY Straight Micro HDMI Plug Adapter If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of our HDMI ribbon cables, then swap and switch any of our HDMI adapters on each end using the flex cable...

Heat shrink is the duct tape of electronics which I guess makes this heat shrink the colorful and exciting duct tape they sell at craft stores. This heat shrink comes in six different colors - red, blue, green, yellow, white and the traditional...

By popular demand, we now have a handy extension cord for all of our JST-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH socket, and the other end has a matching plug. Between the two, 500mm of color coded wire...

This cable is a little unusual, rather than having a USB A plug on one end, it has two Micro B USB connections! What is this for? It's for when you have a "USB On-The-Go (OTG)" device, and you want to plug in another USB device. For example, a Pi Zero or...

If you're looking to make a custom cable with any two of our HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the HDMI...

This handy USB extension cable will make it easy for you to enclose a device that has a mini-B USB type port. This would be most handy when putting a Teensy, FTDI friend, USB LiPo charger, USB Boarduino, etc into a box! The jack half has two mounting...

If you're looking to make a custom cable with any two of Adafruit's HDMI adapters, then you'll need to have these flex cables handy! Making custom HDMI cables has never been easier. Just grab one of these cables, then swap and switch any of the...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug...

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab an HDMI ribbon cable, then swap and switch any of our HDMI adapters on each end using the flex cable clips...