* micro:bit

Use this switched battery holder to power your Micro:bit or other device. Equipped with a JST-PH male connector.

ElecFreaks Micro:bit Tinker Kit is a set of Micro:bit accessory that enables you to connect all kinds of modules easily without a group of messy breadboard wires. Features Available for use when being plugged. Rich tutorial cases. Connect limitless...

This product is for educational purpose in schools and other pedagogical contexts. Please use under adult supervision.Suitable for ages over 10 years old. WITHOUT micro: bit!!! ElecFreaks Micro:bit Starter Kit is designed for children who is beginning...

OCTOPUS Potentiometer is a simple linear sliding potentiometer electronic building block module which can be used as a resistor divider output, HID control panel, or in the electronic building block kit. News: All of the Octopus bricks support Scratch...

Octopus Electronic Bricks, you can use them to build electronics projects just as easily as piling bricks. By using Octopus electronic bricks, you can connect Arduino/Freaduino compatible boards easily with various digital, analog and I2C/Uart...

Octopus Electronic Bricks, you can use them to build electronics projects just as easily as piling bricks. By using Octopus electronic bricks, you can connect Arduino compatible boards easily with various digital, analog, and I2C/UART...

Make your micro:bit sing with noise:bit! It's a tiny speaker that packs a fair bit of punch, and it's perfect for BLEEPS and BLOOPS! Just slot in your micro:bit, and use the sound generation blocks and code in Microsoft...

This kit contains everything (except micro:bit) needed to start learning about connecting electronics to the micro:bit in an accessible and easy manner. Everything is connected using the supplied alligator clips, so no soldering required. This kit...

A 3V Light Emitting Diode as an additional LED. It uses a high brightness low current LED and includes a current limiting resistor to protect the micro:bit’s output. The black lead goes on to GND and the green lead goes on to whichever Pin 0, 1...

A transistor that will allow other items to be switched where the micro:bit would not be able to. Items such as motors, larger speakers, relays and so forth, up to 1A total load. A current limiting resistor is in the circuit to protect the micro:bit...

A simple buzzer with transistor that can be powered by the micro:bit. Costs more than a headphone adapter but far less than the mini-speaker - its best use is to act as an sounder for an alarm or similar.

A small version of the PIR that is used in a typical burglar alarm. It triggers when a warm body passes in front of the detector. It has some range / sensitivity setting capability and the duration of the output can be set. The black lead goes on to...

A small microphone with amplifier & threshold setting. It can detect when sound reaches a certain level. It can not detect a particular frequency and there is no support in the micro:bit programming environment at present for it to analyse...

A type of buzzer - it has to be driven by a pulsed output. It's tuned for around 2kHz when it will be at its loudest but will produce a tone across a wide range of frequencies. In the Block Editor, the black lead goes on to GND and the blue lead goes on...

Good for detecting boxes, drawers or doors being opened and much more. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2. This item is somewhat polarity sensitive, the red & black leads need...

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead...

An external light sensor for all your light sensing needs. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2.This item is polarity sensitive, the red & black leads need to be on the correct...

This Pushbutton makes it easy to add an extra input to your BBC micro:bit projects. With simple clip leads and no soldering required, it’s perfect for classrooms, workshops, and quick prototyping. Features Simple connectivity — attach...

Provides a variable voltage to an analog input via a twist knob - a volume control if you will. Can be used for any application where a user input across an analog range is required - for instance changing the frequency of the music output or the speed...

Dupont 5 way Female to Female interface cable for the Kitronik Line Following Add On For :MOVE mini kit. It is also suitable for breadboards with 2.54mm pitch. This standard Dupont interface cable is the cable used in the Kitronik Line Following Add...