Adafruit

Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.6" (66mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input...

RGB Pixels are digitally-controllable lights you can set to any color, or animate. Each RGB LED and controller chip is molded into a 'dot' of silicone. The dots are weatherproof and rugged. There are...

Infrared LEDs are used for remote controls (they're the little LED in the part you point at your TV) and 'night-vision' cameras, and these little blue guys are high powered ones! They are 940nm...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever...

The IS31FL3731 will let you get back to that classic LED matrix look, with a nice upgrade! This I2C LED driver chip has the ability to PWM each individual LED in a 16x9 grid so you can have...

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller. To use, connect pin 3 (all the way to the right) to 5V...

For advanced DotStar LED fans, Adafruit now has a bendable, Flexible 16x16 Dotstar LED Matrix! Control all 256 ultra-bright LEDs using only two microcontroller pins, set each LED as you wish to...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, mini B and USB A socket. Each...

These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber...

By popular demand, we now have these buttons with a full color RGB LED ring light! These chrome-plated metal buttons are rugged, but certainly not lacking in flair. Simply drill a 16mm hole into...

Connect to those pesky 0.5mm pitch connectors that you may run across with an FPC stick. Adafruit designed this for use in house, to quickly connect to 50pin 0.5mm pitch flex cables they need to test...

Transistors are powerful little electronic switches, and when little NPN transistors aren't powerful enough for your project, use these beefy TIP120 Darlington transistors. Great for whenever you...

Display, elegantly, 012345678 or 9! Gaze, hypnotized, at ABCDEFGHIJKLM - well it can display the whole alphabet. You get the point. This is a nice, bright alphanumeric display that shows letters and...

Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is...

Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Plug to Breakout. You get a nice solid PCB with an HDMI plug and through hole pads that you can solder to assemble your...

Make your own custom HDMI cable or HDMI interface with ease, using this HDMI Terminal Block Breakout. You get a nice solid PCB with an HDMI plug and two strips of terminal blocks that you can use...

Make your own custom HDMI input or HDMI interface with ease, using this HDMI Socket to Terminal Block Breakout. You get a nice solid PCB with an HDMI socket and two strips of terminal blocks that you...

Make your own custom HDMI input or HDMI interface with ease, using this HDMI Socket Breakout. You get a nice solid PCB with an HDMI socket that you can solder to assemble your own wiring jigs...

If you've ever ordered and wire up a 9-DOF sensor, chances are you've also realized the challenge of turning the sensor data from an accelerometer, gyroscope and magnetometer into actual "3D space...

Beguiled by a fancy new chip that is only available in a SOIC or MSOP/(T)SSOP pinout? This breakout PCB set will make your life much much easier and get you prototyping faster than ever. One side has...