Categories - PiShop.ca

Sub Categories

Adafruit I2S 3W Stereo Speaker Bonnet for Raspberry Pi - Mini Kit

$20.95

Hey Mr. DJ! Turn up that Raspberry Pi mix to the max with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi. (It's not big enough to be an official HAT, so Adafruit called it a bonnet, you see?) It's the exact same size as a Raspberry...

Add to Cart

Nylon 12mm M2.5 Standoff Set - Pack of 4

$0.95

Nylon Standoffs - M2.5x12mm - Pack of 4 - Black

Add to Cart

Stereo Enclosed Speaker Set - 3W 4 Ohm

$12.94

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. Adafruit likes these speakers as they are small and enclosed for good audio volume and quality. The pair...

Add to Cart

Standalone Momentary Capacitive Touch Sensor Breakout - AT42QT1010

$4.95 $8.95

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor. When a capacitive load is...

Add to Cart

DC-To-Type-C USB Adapter Cable for BOSS Dac v1.2

$2.45

DC To Type-C USB Adapter Cable to be used with the BOSS Dac v1.2. Features 5.5mm x 2.5mm DC female input to TypeC USB male 18 AWG 17cm total length Input: 5.5mm x 2.5mm DC female to type c cable

Notify Me

micro:bit RED LED

$4.75

A 3V Light Emitting Diode as an additional LED. It uses a high brightness low current LED and includes a current limiting resistor to protect the micro:bit’s output. The black lead goes on to GND and the green lead goes on to whichever Pin 0, 1...

Add to Cart

micro:bit Transistor

$3.95 $8.50

A transistor that will allow other items to be switched where the micro:bit would not be able to. Items such as motors, larger speakers, relays and so forth, up to 1A total load. A current limiting resistor is in the circuit to protect the micro:bit...

Add to Cart

micro:bit Buzzer

$5.95 $7.50

A simple buzzer with transistor that can be powered by the micro:bit. Costs more than a headphone adapter but far less than the mini-speaker - its best use is to act as an sounder for an alarm or similar.

Add to Cart

micro:bit Passive Infrared Movement Detector

$8.95 $10.95

A small version of the PIR that is used in a typical burglar alarm. It triggers when a warm body passes in front of the detector. It has some range / sensitivity setting capability and the duration of the output can be set. The black lead goes on to...

Add to Cart

micro:bit Water Pump

$18.75

A small submersible pump designed for Ph neutral, ambient temperature, non-sticky liquids, ie water. It has a transistor interface with current limiting resistor to the micro:bit output and needs ~8V power to run. The black lead goes on to GND, the green...

Notify Me

micro:bit Sound Level Detector

$8.45 $9.50

A small microphone with amplifier & threshold setting. It can detect when sound reaches a certain level. It can not detect a particular frequency and there is no support in the micro:bit programming environment at present for it to analyse...

Add to Cart

micro:bit Piezo Buzzer

$3.95 $5.95

A type of buzzer - it has to be driven by a pulsed output. It's tuned for around 2kHz when it will be at its loudest but will produce a tone across a wide range of frequencies. In the Block Editor, the black lead goes on to GND and the blue lead goes on...

Add to Cart

micro:bit Servo

$11.95

A small motor that moves it's output arm to a position depending on the signal sent to it with a reasonable degree of accuracy & repeatability. The brown lead with the black croc clip goes on to GND, the yellow lead goes on to the Pin 0, 1 or 2 that...

Notify Me

micro:bit Microswitch

$3.95 $4.95

Good for detecting boxes, drawers or doors being opened and much more. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2. This item is somewhat polarity sensitive, the red & black leads need...

Add to Cart

micro:bit Temperature Sensor

$9.75

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead goes...

Add to Cart

micro:bit LDR Light Sensor

$4.95 $7.25

An external light sensor for all your light sensing needs. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2.This item is polarity sensitive, the red & black leads need to be on the correct...

Add to Cart

micro:bit Pushbutton

$3.95 $4.95

A pushbutton on a lead for when you need another pushbutton or you want it away from your micro:bit One lead goes on 3v or GND and the other lead goes on 0, 1, or 2. For advanced applications it is feasible to connect two pins with...

Add to Cart

micro:bit Potentiometer

$5.95 $7.95

Provides a variable voltage to an analog input via a twist knob - a volume control if you will. Can be used for any application where a user input across an analog range is required - for instance changing the frequency of the music output or the speed...

Add to Cart

micro:bit Water Sensor

$7.50

The Water Sensor Provides a variable analog reading depending on how wet/damp the sensor is. Good for plants or fingers. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on whichever pin is being used in the program. This...

Notify Me