Categories - PiShop.ca

Sub Categories

THIS ITEM IS NO LONGER AVAILABLE Discover a new world of play and learning Kids define how they want to play. Whether you're into hosting make-believe tea parties, having jousts at magical kingdoms, or adventuring with friends, Dash will be there every...

Notify Me

littleBits - XOR

$6.95 $12.95

The XOR module is a logic gate with two inputs. Think of it as “exclusive or,” meaning that it sends an on signal when it’s receiving an on signal exclusively from one input or the other, but not both. Real World Example The XOR is...

Notify Me

littleBits - NAND

$6.95 $12.95

The NAND module is a logic gate with two inputs. Think of it as “not and.” The NAND module will always send an on signal unless both input one and input two are receiving an on signal. It’s the exact opposite of the AND module. Real...

Notify Me

littleBits - NOR

$6.95 $12.45

The NOR module is a logic gate with two inputs. As its name suggests, it sends an on signal only when neither input is receiving an on signal. In other words, it’s the exact opposite of the OR module. The NOR module is good for projects in which...

Notify Me

littleBits - Bend Sensor

$0.00

THIS ITEM IS NO LONGER AVAILABLE AS AN INDIVIDUAL COMPONENT The bend sensor turns on as you flex the long strip. To send signal to your output Bits, bend the strip down, towards the Bit's feet. But make sure not to crease it: that could damage your Bit!...

Notify Me

littleBits - MP3 Player

$0.00

THIS ITEM IS NO LONGER AVAILABLE AS AN INDIVIDUAL COMPONENT The mp3 Player allows you to play your very own mp3 files using littleBits. Sending a signal to the mp3 player can make it work as a media player, sampler, or looper. Just load the mp3 files you...

Notify Me

littleBits - Wireless Receiver

$27.95 $54.95

You will need a wireless receiver and a transmitter to use littleBits wirelessly. You can purchase additional receivers and transmitters, but if you are just getting started with littleBits wireless modules, we suggest purchasing the Wireless Boost It...

Notify Me

littleBits - Wireless Transmitter

$27.95 $54.95

Notify Me

Pimoroni OmniVESA

$5.95

The perfect mounting solution for your Raspberry Pi! Simply remove the protective backing from the OmniVESA and follow the instructions below to mount your Raspberry Pi either bare or in any of the most popular cases. The nylon screws provided are...

Notify Me

Small Alligator Clip Test Lead (set of 12)

$5.95

Connect this to that without soldering using these handy mini alligator clip test leads. 15" cables with alligator clip on each end, color coded. You get 12 pieces in 6 colors. Strong and grippy, these always come in handy! We often use these in...

Add to Cart

Adafruit 16-Channel PWM / Servo HAT for Raspberry Pi - Mini Kit

$26.95

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these...

Add to Cart

5V 4A (4000mA) switching power supply - UL Listed

$23.95

Need a lot of 5V power? This switching supply gives a clean regulated 5V output at up to 4 Amps (4000mA). 110 or 240 input, so it works in any country. The plugs are "US 2-prong" style so you may need a plug adapter, but you can pick one up at any...

Add to Cart

FTDI Serial TTL-232 USB Cable

$24.95

Just about all electronics use TTL serial for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to have a serial port anymore. This is a USB to TTL serial cable, with a FTDI FT232RL usb/serial chip embedded in the head...

Notify Me

Heat Sink Thermal Tape - 3M 8810 - 80mm x 80mm

$5.95

Get that heat sink stuck on good and strong with 3M's thermal tape. Specifically designed for attaching heat sinks to ICs. Works better and is less messy than thermal glues or pastes because the thickness is even across the area. A perfect match for our...

Add to Cart

Pi Model A+ Case Base - Clear

$6.95

This is just the base of the Raspberry Pi Model A+ case. You probably need a lid for it. It's here. This is the clear base. It reminds us of...well whatever's inside it. It's clear. Check out our other colors from the...

Notify Me

USB Micro-B Breakout Board

$3.95

Simple but effective - this breakout board has a USB Micro-B connector, with all 5 pins broken out. Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project. We use a micro-AB connector with through-hole shielding...

Add to Cart

Plastic Water Solenoid Valve - 12V - 1/2" Nominal

$11.95

Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. There are two 1/2" (Nominal non-taped National Pipe) outlets. Normally, the valve is closed. When 12VDC is applied to...

Add to Cart

AM2302 (wired DHT22) temperature-humidity sensor

$14.95 $19.95

The AM2302 is a wired version of the DHT22, in a large plastic body. It is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on...

Add to Cart

Bluefruit LE Friend - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v3.0

$24.95 $29.95

The Bluefruit LE Friend is your new BLE BFF! This USB-to-BLE board makes it easy to get your computer talking to your BLE enabled phone or tablet using a standard serial/UART connection. In it's simplest form, it works on the same principle as a common...

Notify Me

Flex Cable for Raspberry Pi Camera - 2 meters

$6.95

This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is...

Notify Me