Categories - PiShop.ca

Sub Categories

A 3V Light Emitting Diode as an additional LED. It uses a high brightness low current LED and includes a current limiting resistor to protect the micro:bit’s output. The black lead goes on to GND and the green lead goes on to whichever Pin 0, 1...

Add to Cart

micro:bit Transistor

$3.95 $8.50

A transistor that will allow other items to be switched where the micro:bit would not be able to. Items such as motors, larger speakers, relays and so forth, up to 1A total load. A current limiting resistor is in the circuit to protect the micro:bit...

Add to Cart

micro:bit Buzzer

$5.95 $7.50

A simple buzzer with transistor that can be powered by the micro:bit. Costs more than a headphone adapter but far less than the mini-speaker - its best use is to act as an sounder for an alarm or similar.

Add to Cart

micro:bit Passive Infrared Movement Detector

$8.95 $10.95

A small version of the PIR that is used in a typical burglar alarm. It triggers when a warm body passes in front of the detector. It has some range / sensitivity setting capability and the duration of the output can be set. The black lead goes on to...

Add to Cart

micro:bit Water Pump

$18.75

A small submersible pump designed for Ph neutral, ambient temperature, non-sticky liquids, ie water. It has a transistor interface with current limiting resistor to the micro:bit output and needs ~8V power to run. The black lead goes on to GND, the green...

Notify Me

micro:bit Sound Level Detector

$8.45 $9.50

A small microphone with amplifier & threshold setting. It can detect when sound reaches a certain level. It can not detect a particular frequency and there is no support in the micro:bit programming environment at present for it to analyse...

Add to Cart

micro:bit Piezo Buzzer

$3.95 $5.95

A type of buzzer - it has to be driven by a pulsed output. It's tuned for around 2kHz when it will be at its loudest but will produce a tone across a wide range of frequencies. In the Block Editor, the black lead goes on to GND and the blue lead goes on...

Add to Cart

micro:bit Servo

$11.95

A small motor that moves it's output arm to a position depending on the signal sent to it with a reasonable degree of accuracy & repeatability. The brown lead with the black croc clip goes on to GND, the yellow lead goes on to the Pin 0, 1 or 2 that...

Notify Me

micro:bit Microswitch

$3.95 $4.95

Good for detecting boxes, drawers or doors being opened and much more. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2. This item is somewhat polarity sensitive, the red & black leads need...

Add to Cart

micro:bit Temperature Sensor

$9.75

A very accurate temperature sensor using a calibrated chip called a TMP36GZ. It is accurate to ±1°C at +25°C. At this temperature it outputs 750mV. It changes by 10mV per °C. The black lead goes on GND, the red lead goes...

Add to Cart

micro:bit LDR Light Sensor

$4.95 $7.25

An external light sensor for all your light sensing needs. The black lead goes on GND, the red lead goes on 3v and the other lead goes on 0, 1, or 2.This item is polarity sensitive, the red & black leads need to be on the correct...

Add to Cart

micro:bit Pushbutton

$3.95 $4.95

A pushbutton on a lead for when you need another pushbutton or you want it away from your micro:bit One lead goes on 3v or GND and the other lead goes on 0, 1, or 2. For advanced applications it is feasible to connect two pins with...

Add to Cart

micro:bit Potentiometer

$5.95 $7.95

Provides a variable voltage to an analog input via a twist knob - a volume control if you will. Can be used for any application where a user input across an analog range is required - for instance changing the frequency of the music output or the speed...

Add to Cart

micro:bit Water Sensor

$7.50

The Water Sensor Provides a variable analog reading depending on how wet/damp the sensor is. Good for plants or fingers. The black lead goes on GND, the red lead goes on 3v and the blue lead goes on whichever pin is being used in the program. This...

Notify Me

TFT FeatherWing - 2.4" 320x240 Touchscreen For All Feathers

$46.94

A Feather board without ambition is a Feather board without FeatherWings! Spice up your Feather project with a beautiful 2.4" touchscreen display shield with built in microSD card socket. This TFT display is 2.4" diagonal with a bright 4 white-LED...

Notify Me

Adafruit HUZZAH32 - ESP32 Feather Board (pre-soldered)

$31.95

Aww yeah, it's the Feather you have been waiting for, this time with pre-assembled headers! The HUZZAH32 is Adafruit's ESP32-based Feather, made with the official WROOM32 module. They packed everything you love about Feathers: built in...

Notify Me

3x4 Right Angle Male Header - 4 pack

$3.95

Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or...

Add to Cart

DiddyBorg v2 Sensor Mount Kit

$14.95 $22.95

Want to add more sensors to your DiddyBorg v2? Our Sensor Mount Kit allows you to add 4x ultrasonics and an extra Pi camera to your robot. The kit consists of: 4x Ultrasonic mounts 1x Camera mount 16x M1.7 screws and nuts 2x...

Notify Me

DiddyBorg v2 Multifunction Top Kit

$12.95 $22.45

Want to add more sensors or an extra tier to your DiddyBorg v2? Our Multifunction Top Kit allows you to extend your robot to do even more :) With the Multfunction Top Kit fitted DiddyBorg v2 can now: Attach two servos to the top...

Notify Me

Mini Black HAT Hack3r – Fully Assembled

$19.95

Mini Black HAT Hack3r – Fully AssembledNeed to detach or debug your HAT? Then the Mini Black HAT Hack3r is for you! A nifty little tool that lets you access all of the GPIO pins while also running a HAT. Ideal for debugging your HAT projects or...

Add to Cart